COSPRO

Micro Fine Tagging Gun Guide

Loading, needle replacement and troubleshooting for your COSPRO micro fine tagging gun.

loading your gun

The pins need to be loaded in the correct direction and locked in place to feed through the gun.

Longer end first. One end of the pin strip has a longer section of plastic extending past the pins. This end goes into the gun first.

  1. Check the ends of the pin strip and position the longer plastic end towards the loading slot.
  2. Gently pull the small lever on top of the gun while inserting the strip.
  3. Guide the strip into position. Don’t force it or push it too far down.
  4. Release the lever to lock the pins in place.
  5. Test on a scrap of fabric before using the gun on your garment.

To reposition or remove the strip, pull the lever to release it first.

troubleshooting

the trigger moves but no pin comes out

Check that there are pins remaining and that the strip has been inserted with the longer plastic end first.

Use the top lever to release and reposition the strip, then release the lever to lock it in place.

If the pins still aren’t feeding, check for a pin caught in the needle. Also check that the needle is fully inserted and locked, with its channel aligned with the pin channel inside the gun.

the gun is jammed or the trigger feels stuck

Stop if the trigger resists. Don’t squeeze harder to try to push the pin through.

Check the pin strip
Make sure the longer plastic end was inserted first. The strip may also be incorrectly seated or pushed too far down. Gently pull the top lever to release it, reposition the strip and release the lever to lock it in place.

Check for a trapped pin
Look for a pin or piece of plastic caught in the needle’s channel. This can block the next pin from passing through. If it won’t come away easily, email us for help.

Check the needle alignment
The channel in the needle needs to line up with the pin channel inside the gun. Make sure the needle is fully seated and its locking mechanism is secured.

Once everything is clear and correctly positioned, test on a scrap of fabric. If the trigger still resists, stop and email us.

the gun keeps jamming

If the gun releases a few pins and then jams again, check that:

  • The pin strip was loaded with the longer plastic end first.
  • The strip is seated correctly, without being pushed too far down.
  • The top lever has been released to lock the strip in place.
  • The needle is correctly aligned and locked.
  • The needle isn’t bent or damaged.
  • You’re using the correct COSPRO refill pins and replacement needle for your gun model.

If it continues to jam, email us and we’ll help you work out what’s happening.

the gun isn’t working after a needle change

Check that you’re using the correct COSPRO replacement needle for your gun model and that it is fully seated and locked in place.

The needle channel must line up with the pin channel inside the gun. If these aren’t aligned, the pins won’t pass through correctly.

See the needle replacement instructions below.

replacing the needle

The needle has a separate locking mechanism from the lever used to load the pins.

  1. Keep your finger off the trigger. Pull the top lever to release and remove the pin strip.
  2. Release the needle lock.
  3. Carefully remove the needle, holding it by the base.
  4. Insert the correct COSPRO replacement needle, lining up its channel with the pin channel inside the gun.
  5. Make sure the needle is fully seated, then secure the needle lock.
  6. Reload the pins with the longer plastic end first, then test on a scrap of fabric.

If the needle won’t sit properly or the lock won’t close, check the alignment and that you have the correct replacement needle. Don’t force it into place.

choosing refill pins and replacement needles

Our micro fine tagging guns are only compatible with COSPRO refill pins and replacement needles. Pins and needles from other brands may look similar but aren’t suitable for use with our guns.

Check the product description to make sure you’re choosing the correct COSPRO pins and needles for your gun model. If you’re unsure, email us and we’ll help.

still having trouble?

Email us at hello@cospro.com.au and we’ll help you get it sorted.